|
|
| Tên thương hiệu: | WELLMAN |
| Số mô hình: | X-6000 |
| Điều khoản thanh toán: | T/T |
| Category | Specifications |
|---|---|
| X-ray Source | Closed microfocus, 90kV max tube voltage, 200μA max tube current, 5μm focal spot, auto preheat |
| Flat Panel Detector | 130mm*130mm effective area, 85μm pixel size, 1536*1536 resolution, 20fps frame rate |
| Table | 420mm*420mm size, 400mm*400mm detectable area, 15kg max load |
| Equipment | 150X geometry magnification, 1500X system magnification, max 3.0s/point inspection speed |
| Dimensions & Weight | 1100mm(L)*1000mm(W)*1600mm(H), 1000kg |
| Power Supply | AC110-220V 50/60HZ, 1300W max power |
| Configuration | Intel I5 CPU, 8G RAM, 240GB SSD, 24" HDMI LCD display |
| Radiation leakage | No leakage, international standard: ≤1μSv/h |
| Lead glass observation window | Transparent lead glass window shields radiation to observe the inner status |
| Window and back door safety interlock | Once users open the window or back door, X-ray tube will power off immediately. When the window or back door is open, users can't turn on the X-ray |
| Electromagnetic safety switch | Lock once the X-ray is on, users can't open the observation window |
| Emergency stop | Next to the operation position, press to power off |
| Tube protection | User can't leave the software if you don't close the X-ray tube |
| Function module | Operation |
|---|---|
| X-ray tube control | Using Keyboard and mouse |
| Status bar | Indicates the interlock status, pre-heat status, and X-ray status by flashing alternately red and green |
| Image effect adjustment | The brightness, contrast and gain of the image can be adjusted freely |
| Product list | Users can save the inspection parameters such as Z-axis position, brightness, contrast and gain |
| Navigation window | The table will move to the place you click and display on the screen |
| Motion axis status | Display real-time coordinates |
| Inspection result | The measurement results (voids rate, distance, area, etc., set by users) display in order |
| Speed control | The movement speed of each axis can be adjusted (slow, normal and fast) |
| Automatic calculation | Click on two points to determine a rectangle |
| Parameters adjustment | Users can adjust the grayscale threshold, pixel, contrast, size filtering and other parameters |
| Add voids manually | Users can draw a polygon or a free figure and calculate it as a void into the void rate |
| Save parameters | Users can save parameters and can directly save the parameters |
| Distance | Click the A and B points to set as the baseline, then click the C point to measure the vertical distance from the C point to the baseline |
| Distance rate | It is mostly used to measure the soldering rate of the through-hole |
| Angle | Click the A and B points to set as the baseline, then click the C point to measure the angle between the BA and BC rays |
| Radius | Click three points to determine a circle and measure the circumference, area and radius |
| Perimeter | Click two points to determine a square, measure the length, width and area |
| Manual setting | Users can set any positions on the table as inspection points, the software will automatically inspect and save the picture |
| Array | Set two of the inspection points and the number of rows and columns, the software will automatically inspect each point and save pictures |
| Automatic identification | The software automatically identifies the positions, takes measurements, and saves the image |
Băng hình
Băng hình
Băng hình
Băng hình
Băng hình
Địa chỉ
5F,B3, Nhà máy công nghiệp điện tử Anda, Cộng đồng Heping, Đường Fuhai, Quận Bảo An, Thâm Quyến
Tel
+86-1840-6666--351
